- About Us
- Tuning Services
- Contact Us
So, you are out car shopping and you have found yourself looking at hatchbacks and found that the Volkswagen MK6 GTI (model years 2010-2014) is appealing to you. Being the good consumer that you are you ask yourself what are the common problems with the MK6 GTI that you should be aware of. You are in luck! Below is a list of what issues we have seen with these vehicles.
Don’t fret based on this list though. These cars have been solid performers when taken care of. As long as you go in with your eyes wide open you will be happy with your decision.
Timing Chain Tensioner
The timing chain tensioner fails resulting in the chain jumping teeth and causing engine damage
An updated part is available and was released in 2013. You can verify if your vehicle has the old or new tensioner through an inspection port located on the lower timing cover. Which you can see to the left of the crank pulley in the image below.
Carbon Buildup on Valves
This is a common issue with direct injection engines. This will cause drivability issues, fuel economy and can lead to a check engine light. Unfortunately, this buildup is inevitable but it can be remedied with a walnut shell blasting. We have written about it in more detail here.
The intake manifold runner flap will break or the position sensor will fail. This will cause intake manifold runner flap position codes. Entire intake manifold will need to be replaced if the runner flap breaks. The sensor is available separately.
The ignition coils will fail causing an engine misfire. If you find one coil is misfiring it is generally a good idea to replace all four of them instead of just the failed coil.
Coolant Temperature Sensor
The coolant temperature sensor will fail causing a performance malfunction in cooling system fault. It is a cheap fix, but we recommend sourcing your sensor from the dealer. For whatever reason, we have found these to be more durable than the ones sourced from aftermarket sources.
The rod on the wastegate can have excessive play causing a rattle noise. If caught early enough VW does have a clip that can be installed to eliminate the rattle. However, this is usually not very successful and turbo replacement is ultimately required.
High Pressure Fuel Pump
While not as common as the FSI engines, the high pressure fuel pump still can fail on the TSI engines found in the MK6 GTI. Typically you will see fuel pressure faults indicating a potential failure.
The diaphragm fails in the PCV valve which can cause a squealing noise and/or check engine light from an idle air control too high or a lean code. This valve sits on top of the valve cover and is a relatively easy fix. If left too long it can also causes premature failure of the rear main seal described below.
Rear Main Seal Failure
The rear main seal will start to leak oil and can also lead to misfire or lean codes causing a check engine light. It seems that these primarily fail due to excessive crankcase pressure caused by failed PCV valves as described above. It is required to remove the transmission to replace, so if you find it on a pre-purchase inspection keep this in mind.
The diverter valve or air recirculation valve fails. The early model version utilized a diaphragm that would tear and cause under-boost codes. There is an updated piston-style diverter valve that does not tear. Of course, there are always aftermarket options as well if you are so inclined.
Water pump fails with a higher than normal rate resulting in leaking coolant and overheating.
Evap Purge Valve
The evap purge valve (N80 valve if you are looking at the VW description) is a solenoid valve that controls the amount of fuel vapor directed back to the engine to be burned. The valve will stick open and cause a free flow of air. When the car performs its tank pressurization test it will throw a code because it thinks there is a leak in the system due to the open valve.
Fuel Pump Control Module
The fuel pump control module sits underneath the rear seat above the fuel pump. This module can overheat and cause the car to cut out. They can actually get hot enough to actually melt the plastic casing causing a fire hazard. Generally, not a good idea when it is so close to a tank of gasoline. There is a revised part from VW to address the problem.
When you are in need of expert Volkswagen repair or performance tuning for your new GTI give Alex’s Autohaus a call at (801) 566-6115 and we would love to help you get the most out of your vehicle.
Make sure to subscribe to our newsletter and be the first to know the news.
Alex’s Autohaus offers all customers the Bosch and Tech-Net Peace of Mind Nationwide Warranty. The 36 month/36,000 mile warranty is honored at over 10,000 service centers across the country. Our 36,000 mile warranty is the best in the business!Read More (801) 566-6115